- Manuals
- Brands
- CountyLine Manuals
- Tiller
- 17306
- Operator's manual
Crt tiller
Hide thumbs
-
- Contents
- Table of Contents
- Troubleshooting
- Bookmarks
Table of Contents
-
Crt Tiller
-
Table of Contents
-
Registration
-
Warnings and Safety Precautions
-
Maintenance and Storage
-
Safety Decals
-
-
Assembly
-
Features
-
Operation
-
Belt Tension Adjustment
-
Tilling Tips
-
- Maintenance
- General Maintenance
-
Storage
-
Troubleshooting
-
Warranty
- Parts
-
CRT Tiller
-
Dipstick Cut-Outs
Advertisement
Quick Links
- 1 Assembly
- 2 Operation
- 3 Maintenance
- 4 General Maintenance
- 5 Parts
- Download this manual
Operator's Manual
Original Operating Instructions
17306
CRT Tiller
GAS/OIL
RATIO
50:1
Product #: 17306
P/N: 17459
ECN: 10117
REV1: 09/04/13
Email for more information
© 2014 Ardisam, Inc.
info@ardisam.com
All Rights Reserved
Table ofContents
Advertisement
Table of Contents
Related Manuals for CountyLine 17306
-
Tiller CountyLine 17455 Operator's Manual
Front tine tiller (24 pages)
-
Tiller CountyLine 20969 Operator's Manual
(32 pages)
Summary of Contents for CountyLine 17306
-
Page 1: Crt Tiller
Operator's Manual Original Operating Instructions 17306 CRT Tiller GAS/OIL RATIO 50:1 Product #: 17306 P/N: 17459 ECN: 10117 REV1: 09/04/13 Email for more information © 2014 Ardisam, Inc. info@ardisam.com All Rights Reserved... -
Page 2: Table Of Contents
17306 CRT Tiller INTRODUCTION Thank you for purchasing the 17306 CRT Tiller from CountyLine®. We have worked to ensure that this tiller meets the highest standards for usability and durability. With proper care, your tiller will provide many years of service. -
Page 3: Warnings And Safety Precautions
• Readandfollowallsafetyinstructions. • Carefullyfollowallassemblyinstructions. WARNING • Maintainthetilleraccordingtodirectionsandschedule WARNING INDICATES A SERIOUS INJURY OR FATALITY included in this CountyLine operator’s manual. COULD RESULT IF THE SAFETY INSTRUCTIONS THAT • Ensurethatanyonewhousesthetillerisfamiliarwithall FOLLOW THIS SIGNAL WORD ARE NOT OBEYED. controls and safety precautions. - Page 4 • See manufacturer’s instructions for proper operation and lever is released into the neutral position. If it does rotate installation of accessories. Only use accessories approved when in neutral, contact CountyLine customer service for by the manufacturer. instruction. • Operate only in daylight or good artificial light.
- Page 5 Operator’s Manual 17306 CRT Tiller ENGINE SAFETY PRECAUTIONS WARNING Warning Carbon Monoxide Poisoning ENGINES GIVE OFF CARBON MONOXIDE, AN ODOR- Engines give off carbon monoxide, an odorless, colorless, LESS, COLORLESS, POISONOUS GAS. CARBON MON- poisonous gas. Carbon monoxide may be present even if you do OXIDE MAY BE PRESENT EVEN IF YOU DO NOT SMELL not smell or see any engine exhaust.
-
Page 6: Maintenance And Storage
Operator’s Manual 17306 CRT Tiller OPERATION SAFETY RULES IMPORTANT • Neveroperatethetillerwithoutguards,coversandhoodsin THE RIGHT AND LEFT SIDES OF YOUR place. ROTOTILLER ARE DETERMINED FROM • Neverstarttheengineoroperatethetillerwiththewheels THE OPERATING POSITION AS YOU FACE in the free-wheel position. Make sure the wheel lock pins THE DIRECTION OF FORWARD TRAVEL. -
Page 7: Safety Decals
H: Do Not Service or Adjust Moving Parts Unless Engine is Stopped the complete safety instruction text in this manual. For additional and Spark Plug Wire is Disconnected. questions contact CountyLine customer service. I: Dress Appropriately And Wear Sturdy Footwear. J: Toxic Fumes —Do Not Operate in Unventilated Areas. -
Page 8: Assembly
Operator’s Manual 17306 CRT Tiller ASSEMBLY IMPORTANT Your rototiller comes fully assembled except for a few parts. THE RIGHT AND LEFT SIDES OF YOUR The following instructions will help you unpack your tiller and ROTOTILLER ARE DETERMINED FROM assemble and adjust your tiller’s depth regulator lever, cable THE OPERATING POSITION AS YOU FACE tension and handle bar height. - Page 9 Operator’s Manual 17306 CRT Tiller ATTACH HANDLE BAR 1. Locate handle bar extensions. SEE FIGURE 2 handle bar extensions 2. Place handle bar extensions on outside of lower handle bar mount. Line up the handle bar extension pieces with the lower handle bar mount as shown in the decal located on the lower handle bar mount next to the mounting location.
-
Page 10: Features
Operator’s Manual 17306 CRT Tiller FEATURES forward drive safety control lever handlebar forward cable handle bar height adjustment depth regulator lever detent pin tine hood choke side shield tines recoil start belt guard wheel lock pin on/off and wheels throttle control... -
Page 11: Operation
Operator’s Manual 17306 CRT Tiller OPERATION CAUTION PREPARATION PLEASE DO NOT START YOUR TILLER UNTIL YOU HAVE READ THE MANUAL THAT CAME WITH YOUR • Dressappropriatelywhenoperatingthetiller.Alwayswear ENGINE, AND THE SECTIONS IN THIS MANUAL TITLED sturdy footwear. Never wear sandals, sneakers or open shoes, CONTROLS, ADJUSTMENTS AND SAFETY. - Page 12 Operator’s Manual 17306 CRT Tiller START-UP CAUTION The controls required to start and run the rototiller are located THIS INFORMATION IS PROVIDED HERE ONLY TO on the engine and are the choke lever, throttle lever and On/Off INTRODUCE THE CONTROLS. DO NOT START THE switch.
- Page 13 Operator’s Manual 17306 CRT Tiller DRIVE SAFETY CONTROL LEVER WARNING Pull the drive safety control lever toward the handle bar to the TEMPERATURE OF MUFFLER AND NEARBY AREAS MAY FORWARD position to engage the wheels and tines. Releasing EXCEED 150° F. AVOID THESE AREAS.
- Page 14 Operator’s Manual 17306 CRT Tiller WHEEL LOCK PINS WARNING To place wheels in free-wheel position: DO NOT ADJUST TILLING DEPTH UNLESS DRIVE SAFETY CONTROL LEVER IS RELEASED TO NEUTRAL This allows wheels to turn freely on the axle for easy transportation.
-
Page 15: Belt Tension Adjustment
Operator’s Manual 17306 CRT Tiller BELT TENSION ADJUSTMENT CAUTION Proper belt tension is critical to good performance. After 1/2 hour of operation, all cables may have to be adjusted due to initial ALWAYS MAINTAIN CONTROL OF YOUR TILLER. ONLY stretch. Thereafter, check tension after every 2 hours of operation. -
Page 16: Maintenance
If you prefer, your local authorized dealer can make these checks and perform the required procedures for you. Important: Use only approved CountyLine spare parts. Engine must be turned off and cool, and spark plug wire must be removed and secured from spark plug before checking and adjusting engine or equipment. - Page 17 Operator’s Manual 17306 CRT Tiller CHANGE FORWARD BELT CAUTION 1. Turn off engine. Engine must be cool. DO NOT OPERATE TILLER BEFORE READING THE EN- 2. Remove spark plug wire and secure from spark plug. GINE MANUAL PROVIDED IN THE PARTS PACKET.
- Page 18 Operator’s Manual 17306 CRT Tiller ENGINE MAINTENANCE IMPORTANT Refer to the engine manual included in your parts packet for ENGINE IS SHIPPED FROM FACTORY WITHOUT OIL. information on engine maintenance. Your engine manual YOU MUST ADD ENGINE OIL BEFORE STARTING provides detailed information and a maintenance schedule for ENGINE.
-
Page 19: Storage
Operator’s Manual 17306 CRT Tiller CHECK OR FILL ENGINE CRANKCASE WARNING 1. Add oil according to engine manual. Do not overfill. Use a DO NOT STORE TILLER IN AN UNVENTILATED AREA clean, high quality 4-cycle engine oil. Use no special additives WHERE FUEL FUMES MAY REACH FLAME, SPARKS, with recommended oils. -
Page 20: Troubleshooting
Operator’s Manual 17306 CRT Tiller TROUBLESHOOTING WARNING PRACTICE SAFETY AT ALL TIMES. ENGINE MUST BE TROUBLESHOOTING GUIDE TURNED OFF AND ALLOWED TO COOL, AND SPARK While normal care and routine maintenance will extend the PLUG WIRE MUST BE DISCONNECTED AND SECURED life of your rototiller, prolonged or constant use may eventu- BEFORE ATTEMPTING ANY MAINTENANCE OR REPAIR. -
Page 21: Warranty
Operator’s Manual 17306 CRT Tiller WARRANTY TERMS AND CONDITIONS PRODUCT WARRANTY: 1-YEAR LIMITED WARRANTY Ardisam, Inc. (Ardisam) warrants the product(s) under a one-year limited warranty to be free from defects in the material or workmanship or both for a period not exceeding twelve consecutive months from the date of original purchase by the first retail consumer or first commercial end user. - Page 22 Operator’s Manual 17306 CRT Tiller CRT MOTOR MOUNT PARTS 13 10 For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5...
-
Page 23: Parts
Operator’s Manual 17306 CRT Tiller CRT MOTOR MOUNT PARTS LIST R E F. PART # DESCRIPTION QTY. R E F. PART # DESCRIPTION QTY. BOLT, 5/16-24 X 1 HH GR5 WF38 WASHER, FLAT 3/8 STANDARD ZINC LOCKWASHERSPRING5/16” 48144 BOLT, 3/8-16 X 2 HHCS GR5 ZN WF516 WASHER, FLAT 5/16”... - Page 24 Operator’s Manual 17306 CRT Tiller CRT HANDLEBAR AND HOOD PARTS AND PART LIST REF. NO. PART # DESCRIPTION QTY. REF. NO. PART # DESCRIPTION QTY. 17493 WELDMENT, ENGINE/HANDLE 53606 NUT10-24HNYLKZN MOUNT 53613 LINK91/2”LONG 2001 BOLT 3/8-16 X 1-3/4 HH GR5 ZN...
- Page 25 Operator’s Manual 17306 CRT Tiller CRT WHEEL & TILLER SHAFT PARTS & PARTS LIST REF. PART # DESCRIPTION QTY. REF. PART # DESCRIPTION QTY. 331063 BOLT, M6 X 25MM 1500P113 KEY,WOODRUFF 1508 COVER, REAR TRANSMISSION SHAFT, TINE 1507 GASKET,FRONT&REAR HOUSING, TRANSMISSION...
- Page 26 Operator’s Manual 17306 CRT Tiller CRT TINES & HOOD PARTS For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5...
-
Page 27: Dipstick Cut-Outs
Operator’s Manual 17306 CRT Tiller CARDBOARD STENCILS CRT TINES & HOOD PARTS LIST FOR DIPSTICK CUT-OUT R E F . PART # DESCRIPTION QTY. BOLT, 5/16-18 X 1/2 HH GR5 LOCKWASHER,SPRING5/16” DO NOT DO NOT 8930 BOLT, 1/4-20 X 3/4 HH GR5 ZN... - Page 28 Distributed by: 1160 8th Avenue, PO Box 666 Tractor Supply Co.® Cumberland, WI 54829 200 Powell Place 800-345-6007 | Fax: 715-822-2223 Brentwood, TN 37027 E-mail: info@ardisam.com www.TractorSupply.com All weights, specifications and features are approximate and are subject to change without notice. Due to continuous product improvements, product images may not be exact.